rivestimenti murali da esterno

TR-EXTERIOR

Thermally insulating elastomeric exterior wall covering with a high fill factor, composed of special highly insulating microspheres. It provides insulation and insulation from the walls and the exterior, preventing heat exchange with the interior of the home.

There will thus be no thermal bridges and therefore no energy waste, to the advantage of living comfort.

High resistance to bad weather and thermal shocks.

The resistance to algae growth is certified with test report n.15LA01419

  • SUPPORTS

    Civil plaster, panels, fiber cement, concrete, metal, wood, sandwich panels, fabrics

  • APPLICATION

    Vertical

  • SETTINGS

    Outside

  • YIELD

    75 m2 / 12.5 litre drum

  • WATER BASED

  • SOLVENT FREE

  • ENERGY SAVING

  • EXCELLENT PERFORMANCE

rivestimenti murali da esterno

REGULATION (EU) N. 305/2011 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL
March 9, 2011

Test Result UNI EN 1504-2 requirements

Determination of adhesion by direct traction

UNI EN 1542

Fh=0.9 MPa

 

Flexible System

≥0,8 (0,5) MPa

without traffic

 

≥0,8 (1.0) MPa

with traffic
Permeability to carbon dioxide UNI EN 1062-6

Sd co2=139.233 m

Thickness = 288 μm

μ = 483448

 Sd co2>50 m
Degree of transmission of liquid water (permeability) UNI EN 1062-3 W=0.011 kg/(m² h0,5 )  w=0.1 kg/(m² h0,5 )

Degree of water vapor transmission (permeability)

UNI EN ISO 7783

Sd = 0.6095 m

Thickness = 291 μm

μ = 2095

Class I

Indicate class

Class I

Specifications

CLASSIFICATION

  • Test report no.15LA01494 issued by INNOVHUB experimental stations for industry in Milan.
  • Determination of the algaecidal power UNI EN 15458: 2014
  • No algal development
  • Determination of solar reflectance ASTM E 903-12
  • TSR 82

COV CLASSIFICATION (Directive 2004/42 / EC) Law Decree No. 161/2006

  • External wall paints of mineral development Base ACQUA c / BA
  • EU limit value for this product since 2012: 40 g / l
  • TR-EXTERIOR contains maximum VOC <13 g / l

PREPARATION OF THE SUBSTRATES

NEW UNPAINTED SURFACES
Make sure the surface is dry, clean and well cured (at least 30 days). If necessary, apply a coat of good quality PRIMER fixative.

SURFACES ALREADY PAINTED OR DETERIORATED
Brush to remove any loose debris or crumbling parts that are detaching.
In the presence of mold, treat the surface with special products and let it dry before painting.
Remove any efflorescence present by brushing or washing.

APPLICATION PROCEDURE

After preparing the substrate and its complete drying, proceed with the application of the appropriately diluted TR-EXTERIOR paint.
Apply the second coat after 6-8 hours.
The waiting time between one coat and the other is strongly influenced by climatic conditions.
In the event of low temperatures, the waiting time also increases up to 24 hours.
The optimal application temperature is between +10 and + 35 ° C with relative humidity below 70%, but with possible alterations of the finish due to an imperfect film formation of the product.

COLORS

The coloring is achievable through the tintometric system.
In the case of coloring of several packs of the same color it is advisable to use bases from the same production batch.
In case this is not possible to mix the various productions together in order to avoid any differences in tone;

SAFETY INSTRUCTIONS

Sufficiently ventilate the room after painting before staying there again.
Dispose of empty containers according to local regulations.
For further information consult the relative safety data sheet.

NOTES

The information contained in this sheet is only the result of the knowledge available at the date of the same by the manufacturer.
No responsibility is assumed for damage to persons or property resulting from improper use of this information.
The manufacturer reserves the right to change the data without notice.

Subscribe to the newsletter